Youtube Channel
scrivimi: fraranux@gmail.com
chiamami: 345 04.22.\pi

venerdì 20 dicembre 2013

Cosa NON fare con Arduino #3

Cosa NON fare con Arduino #2


a tal proposito:
http://youtu.be/Bt9zSfinwFA

Cosa NON fare con Arduino #1

I primi effetti collaterali della sindrome pre-natalizia.
Lo schema elettrico è estremamente semplice:

















Qui sotto tutto il codice necessario:

/*
 * Oscilloscope Christmas Tree
 *
 *   Created: Dec 10, 2011
 *  
 * Author: John M. De Cristofaro
 *
 * License: This code CC-BY-SA 3.0 and is unsupported.
 * (see creativecommons.org/licenses for info)
 *
 */

/* ****************************************************************************
Fritzing is here:

http://www.flickr.com/photos/johngineer/6496005491/sizes/z/in/photostream/

in case you can't see the image, the following circuit is on both PWM ports

      R
PWM OUT ----/\/\/\-----+------------ OUTPUT
      |
     === C
                       |
                      GND

R = 10k
C = 0.1uF

Use of a 16Mhz xtal/ceramic resonator is strongly suggested.

**************************************************************************** */

#define TRACE_DELAY 2500  // trace delay in uS. making this longer will
     // result in a straighter drawing, but slower
     // refresh rate. making it too short will result
     // in an angular blob.

#define NUM_POINTS 19    // our tree is defined by 19 x/y coord. pairs

#define X               6     // attach scope channel 1 (X) to pin 6
#define Y               5     // attach scope channel 2 (y) to pin 5


// x coords for drawing the tree (in rough clockwise order, from bottom)
unsigned char x_points[NUM_POINTS] = { 110, 110, 50, 80, 65, 95, 80, 110, 95, 125,
155, 140, 170, 155, 185, 170, 200, 140, 140 };

// y coords
unsigned char y_points[NUM_POINTS] = { 15, 35, 35, 85, 85, 135, 135, 185, 185, 235,
185, 185, 135, 135, 85, 85, 35, 35, 15 };

void setup()
{
  pinMode(X, OUTPUT);
  pinMode(Y, OUTPUT);

  // The following sets the PWM clock to maximum on the Arduino(no CPU clock division)
  // DO NOT CHANGE THESE UNLESS YOU KNOW WHAT YOU ARE DOING!
  
  TCCR0A = ( 1<<COM0A1 | 0<<COM0A0 | // clear OC0A on compare match (hi-lo PWM)
1<<COM0B1 | 0<<COM0B0 | // clear OC0B on compare match (hi-lo PWM)
1<<WGM01  | 1<<WGM00); // set PWM lines at 0xFF

  TCCR0B = ( 0<<FOC0A | 0<<FOC0B | // no force compare match
0<<WGM02 | // set PWM lines at 0xFF
0<<CS02 | 0<<CS01 | // use system clock (no divider)
1<<CS00 );

  TIMSK0 = ( 0<<OCIE0B | 0<<TOIE0 |
0<<OCIE0A );  

}

void loop()
{
    unsigned char t;
    {
      for(t = 0; t < NUM_POINTS; t++) // run through the points in x & y
      {
        analogWrite(X, x_points[t]);
        analogWrite(Y, y_points[t]);
delayMicroseconds(TRACE_DELAY); // wait TRACE_DELAY microseconds
      }
    }
}




Circuito e software li ho presi da qui.